EN AW-Al Mn0,6 | EN AW-3207 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full AccessMaterial Description
| Material Number | Material Number (single) | Standard | Range of Application | Standard Status | Country | Predecessor | Successor | Remark |
|---|---|---|---|---|---|---|---|---|
| EN AW-3207 (DIN EN 573-3 : 2007-11) | EN AW-3207 | DIN EN 573-3 : 2007-11 | DIN EN 573-3 : 2007-11 replaced by DIN EN 573-3 : 2007-11 | Replaced | Germany | EN AW-Al Mn0,6 | EN AW-Al Mn0,6 | Material EN AW-Al Mn0,6 is produced for centre punching as well as for prematerial for cans, caps, stoppers. It is useds for sheet metal, strip, plates. The material is food-safe. To the comparable mark AlMn0,6, material No. 3.0506 acc. to DIN 1725-1 : 1983-02 applies: The alloy AlMn0,6 is a low-alloyed AlMn- alloy intended to be used in packaging industry. Mn increases strength in comparison to pure aluminium, but is does not affect corrosion resistance. The alloy pertains to naturally hard aluminium materials. A strength increase can only be achieved by cold forming, not by controlled heat treatment. It is ideal for warm and cold forming, it shows no tendency to earing. It is therefore ideal for deep-drawing. Application: In packaging industry as tear open lids, for general metal goods and metal signs. |
Chemical Composition
| Cu [%] | Fe [%] | Mg [%] | Mn [%] | Si [%] | Zn [%] | Source | Remark |
|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Designation of the delivered Condition DIN | Delivery Condition EN | Nominal Size [mm] | Temperature [°C] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A50 [%] | Source | Remark |
|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Cross Reference
| Material Name | Country | Standard |
|---|---|---|
| AA 3207 | USA | International Registration Record (AA) |
| AlMn0,6 | Turkey | TS 412 |
| A93207 | USA | UNS |
| AlMn0,6 (3.0506) | Germany | DIN 1725-1 |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| EN AW-AlMn0,6 | TRIMET ALUMINIUM AG, Essen |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
EN AW-Al Mn0,6 (EN AW-3207; DIN EN 573-3 : 2007-11)
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Poisson's ratio |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Alternating stress [MPa] | Cycles |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Source description |
|---|---|
| blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
EN AW-Al Mn0,6 (H27 (strain-hardened and partially annealed - 7/8 hard); sheet; 0.200-0.300mm)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
EN AW-Al Mn0,6 (H47 (strain-hardened and painted or lacquered - 7/8 hard); sheet; 0.200-0.300mm)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
EN AW-Al Mn0,6 (H28 (strain-hardened and partially annealed - 4/4 hard (fully hardened)); sheet; 0.200-0.300mm)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
EN AW-Al Mn0,6 (H48 (strain-hardened and painted or lacquered - 4/4 hard); sheet; 0.200-0.300mm)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
EN AW-Al Mn0,6 (H19 (strain-hardened - extra hard); sheet; 0.200-0.300mm)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |