EN AC-Al Si11Cu2(Fe) | EN AC-46100 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full AccessMaterial Description
| Material Number | Material Number (single) | Standard | Range of Application | Standard Status | Country | Successor | Remark |
|---|---|---|---|---|---|---|---|
| EN AC-46100 (DIN EN 1706 : 1998-06) | EN AC-46100 | DIN EN 1706 : 1998-06 | DIN EN 1706 : 1998-06 replaced by DIN EN 1706 : 2013-12 | Replaced | Germany | EN AC-Al Si11Cu2(Fe) | Material EN AC-AlSi11Cu2(Fe) is produced as diecast. It shows the following casting characteristics and properties: plasticity: excellent heat crack resistance: good pressure tightness: acceptable workability (after heat-treatment): acceptable corrosion resistance: insufficient decorative anodic oxidation: not advisable weldability: unsuitable polishability: acceptable strength at room temperature: good strength at increased temp. (up to 200°C): good ductility (impact strength): insufficient fatigue strength amounts 60 to 90 N/mm² ( best available casting method, values for vibration durability up to 50*10 hoch 6 cycles [Woehler diagram]). Diecasting weldability depends on the embedded gas amount and is mostly insufficient. For certain casting methods are achievable good to acceptable values. |
Chemical Composition
| Cr [%] | Cu [%] | Fe [%] | Mg [%] | Mn [%] | Ni [%] | Pb [%] | Si [%] | Sn [%] | Ti [%] | Zn [%] | Source | Remark |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Mechanical Properties
| Casting Method | Condition | Temperature [°C] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A50 [%] | Hardness HB | HBW | Source |
|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur |
Physical Properties
| Temperature [°C] | Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] | Thermal Conductivity [W/(m*K)] | Electric Conductivity [MS/m] | Source |
|---|---|---|---|---|
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] vs Temperature [°C]
Exclusive Insight Locked!
This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.
Unlock NowMaterial Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
EN AC-Al Si11Cu2(Fe) (EN AC-46100; DIN EN 1706 : 1998-06)
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Poisson's ratio |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Alternating stress [MPa] | Cycles |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Coefficient thermal expansion
| Related Temperature [°C] | Temperature [°C] | Coefficient thermal expansion [10^-6*K^-1] |
|---|---|---|
| blur | blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Thermal conductivity
| Temperature [°C] | Thermal conductivity [W/(m*K)] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Source description |
|---|---|
| blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
EN AC-Al Si11Cu2(Fe) (cast condition)
Yield strength
| Temperature [°C] | 0.2% Proof strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Source description |
|---|---|
| blur | blur |