Cu-DHP | CW024A Material Datasheet

Material Test Series Values

Material Standard Values

Material Models for Simulation

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Material Description

Material Number	Material Number (single)	Standard	Range of Application	Standard Status	Country	Remark
CW024A (DIN EN 12163 : 1998-04)	CW024A	DIN EN 12163 : 1998-04	DIN EN 12163 : 1998-04 replaced by DIN EN 12163 : 2011-08	Replaced	Germany	Cu-DHP, mat. No CW024A, is a phosphoric pure copper grade. To the comparable DIN-mark SF-Cu, mat. No 2.0090 acc. to DIN 1787 applies: The material is a deoxidized copper with Cu >= 99,9% and a high residual copper-content. Tensile strength and Brinell hardness are increasable by cold forming. SF-Cu (Cu-DHP) is hydrogen resistant and shows the lowest thermal and electrical conductivity of the pure copper materials. Processing properties: hot forming: very good cold forming: very good machinability: unfavorable hard soldering: very good soft soldering: very good gas-shielded welding: very good burnishing: very good Application: SF-Cu is the most important copper-grade for pipes due to its very good soldering and welding properties. Further application in apparatus engineering and construction trade. For the electrolytically tinned strip the coatings (Sn bright, Sn matt, Sn fuzed, SnPb) are listed by the application (better solderability, better corrosion resistance, reduction of the electrical contact resistance, better appearance) in the DIN EN 14436 : 2004-11 (Table 5)

Chemical Composition

Cu [%]	P [%]	Source
blur	blur	blur

Mechanical Properties

Semi-finished Product	Condition	Strength Abbrevation	Nominal Size [mm]	Temperature [°C]	Tensile Strength [MPa]	Yield Strength (0.2% offset) [MPa]	Elongation A10 [%]	Elongation A100 [%]	Elongation A [%]	Hardness HB \| HBW	Hardness HV	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Physical Properties

Condition	Temperature [°C]	Melting Temperature [°C]	Density [g/cm³]	Young's Modulus [GPa]	Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1]	Thermal Conductivity [W/(m*K)]	Specific Electrical Resistance [µΩm]	Mean Specific Heat Capacity [kJ/(kg*K)]	Electric Conductivity [MS/m]	Source
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Young's Modulus [GPa] vs Temperature [°C]

Exclusive Insight Locked!

This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.

Unlock Now

Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] vs Temperature [°C]

Exclusive Insight Locked!

This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.

Unlock Now

Creep Rupture Behaviour

Condition	Temperature [°C]	Creep Tensile Strength at 10³ h [MPa]	Creep Tensile Strength at 10^4 h [MPa]	1% Creep Limit at 10³ h [MPa]	1% Creep Limit at 10^4 h [MPa]	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur

Heat Treatment

Heat Treatment	Temperature [°C]	Source	Remark
blur	blur	blur	blur
blur	blur	blur	blur
blur	blur	blur	blur

Cross Reference

Material Name	Country	Standard
Cu-DHP	Europe	EN 12163
Cu-DHP	International	ISO/R 1430
C12200	USA	UNS
C12200	USA	ASME B16.22
C12200	USA	ASME B16.29
C12200	USA	ASME SB-111
C12200	USA	ASME SB-152
C12200	USA	ASME SB-359
C12200	USA	ASME SB-395
C12200	USA	ASME SB-42
C12200	USA	ASME SB-543
C12200	USA	ASME SB-75
C12200	USA	ASTM B 101
C12200	USA	ASTM B 111
C12200	USA	ASTM B 152
DHP	USA	ASTM B 224
C12200	USA	ASTM B 272
C12200	USA	ASTM B 302
C12200	USA	ASTM B 306
C12200	USA	ASTM B 359
C12200	USA	ASTM B 360
C12200	USA	ASTM B 370
DHP	USA	ASTM B 379
C12200	USA	ASTM B 395
C12200	USA	ASTM B 42
C12200	USA	ASTM B 432
C12200	USA	ASTM B 447
DHP	USA	ASTM B 5
C12200	USA	ASTM B 543
C12200	USA	ASTM B 640
C12200	USA	ASTM B 68
C12200	USA	ASTM B 687
DHP	USA	ASTM B 698
C12200	USA	ASTM B 716
C12200	USA	ASTM B 743
C12200	USA	ASTM B 75
C12200	USA	ASTM B 819
C12200	USA	ASTM B 837
C12200	USA	ASTM B 88
C12200	USA	ASTM B 903
C12200	USA	ASTM B 919
C12200	USA	FED WW-P-377
C12200	USA	MIL MIL-T-22214
C12200	USA	MIL MIL-T-24107
C12200	USA	MIL SPEC MIL-B-18907
C12200	USA	SAE J 461
C12200	USA	SAE J 463
SF-Cu	Germany	DIN 1708
SF-Cu	Germany	DIN 1787
2.0090	Germany

Producer/Supplier/Trade names

Tradename	Supplier
219	William Prym Holding GmbH, Stolberg
3060	VDM Metals GmbH, Frankfurt/Main
Cu	G.Rau GmbH & Co. KG, Pforzheim
Cu	Eduard Hueck, Lüdenscheid
F30	Eduard Hueck, Lüdenscheid
K 20	Wieland-Werke AG, Ulm
K 21	Wieland-Werke AG, Ulm
KD 30	Sundwiger Messingwerk GmbH & Co.KG, Hemer
SF-Cu	ThyssenKrupp Schulte GmbH, Essen
SF-Cu	F. Hackländer GmbH, Kassel
SF-Cu	KME Germany AG & Co.KG, Menden
SF-Cu	KME Germany AG & Co.KG, Osnabrück
SF-Cu	Emil Müller GmbH, Reichshof-Hespert
SF-Cu	MGI GmbH, Olpe
SF-Cu	CUMSAL GmbH, Wilnsdorf
SF-Cu	CSN Carl Schreiber GmbH, Neunkirchen
SF-Cu	Wieland-Werke AG, Velbert
SF-Cu	KME Germany AG & Co.KG, Osnabrück
SF-Cu	Nussbaum Metallhandel GmbH, Bad Wörishofen
SF-Cu	MPG Mendener Präzisionsrohr GmbH, Menden
SF-Cu	Feindrahtwerk Adolf Edelhoff GmbH & Co, Iserlohn
SF-Cu	Wieland Prometa GmbH, Düsseldorf
SF-Cu	ATI Flat Rolled Products GmbH, Remscheid
SF-Cu	Eugen Geyer GmbH, Königsbach-Stein
SF-Cu	Metall Dittrich, Velbert
SF-Cu	Wieland Prometa GmbH, Düsseldorf
SF-Cu	Manfred J.C. Niemann, Bremen
SF-Cu	Swissmetal Lüdenscheid GmbH, Lüdenscheid
SF-Cu WICU	Mittelrheinische Metallgießerei H. Beyer GmbH & Co KG, Andernach
SF-Cu WICU	DELWO Metallhandel GmbH, Neunkirchen
SF-Kupfer	VDM Metals GmbH, Frankfurt/Main
TECU	KME Germany AG & Co.KG, Osnabrück
TECU-Patina	KME Germany AG & Co.KG, Osnabrück
TECU-STRUCTUR	KME Germany AG & Co.KG, Osnabrück

Material Compliance

REACh	RoHS
blur	blur

Cu-DHP (CW024A; DIN EN 12163 : 1998-04)

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Poisson's ratio
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur

Electrical resistivity

Temperature [°C]	Specific electrical resistance [µΩm]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Coefficient thermal expansion

Related Temperature [°C]	Temperature [°C]	Coefficient thermal expansion [10^-6*K^-1]
blur	blur	blur
blur	blur	blur
blur	blur	blur

Specific heat

Temperature [°C]	Specific heat [kJ/(kg*K)]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Density

Temperature [°C]	Density [g/cm³]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Thermal conductivity

Temperature [°C]	Thermal conductivity [W/(m*K)]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

WIAM Material	Source description
blur	blur

Designation

Designation	Material number	Source
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

Cu-DHP (soft annealed (+A); 4mm; not specified)

Strain life

Temperature [°C]	Cyclic fatigue strength coefficient [MPa]	Cyclic fatigue strength exponent	Ductility coefficient [Pa]	Ductility exponent	Cyclic strength coefficient [MPa]	Cyclic strain hardening exponent	Young's modulus [GPa]
blur	blur	blur	blur	blur	blur	blur	blur

Classification

Treatment	Dimension [mm]	Failure criteria	Source description
blur	blur	blur	blur

Cu-DHP (soft annealed (+A); 6.35mm; not specified)

Strain life

Temperature [°C]	Cyclic fatigue strength coefficient [MPa]	Cyclic fatigue strength exponent	Ductility coefficient [Pa]	Ductility exponent	Cyclic strength coefficient [MPa]	Cyclic strain hardening exponent	Young's modulus [GPa]
blur	blur	blur	blur	blur	blur	blur	blur

Classification

Treatment	Dimension [mm]	Failure criteria	Source description
blur	blur	blur	blur

Cu-DHP (soft annealed (+A); rod; 2.000-80.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R250; rod; 2.000-10.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R250; rod; 10.000-30.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R230; rod; 30.000-80.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R300; rod; 2.000-20.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R280; rod; 20.000-40.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R260; rod; 40.000-80.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (R350; rod; 2.000-10.000mm)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

Cu-DHP (hot rolled)

Yield strength

Temperature [°C]	0.2% Proof strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Source description
blur	blur

Cu-DHP (soft annealed (+A))

Linear-elastic

Temperature [°C]	Young's modulus [GPa]
blur	blur

Classification

Treatment	Source description
blur	blur

Cu-DHP (cold formed)

Linear-elastic

Temperature [°C]	Young's modulus [GPa]
blur	blur
blur	blur
blur	blur
blur	blur

Classification

Treatment	Source description
blur	blur

Cu-DHP | CW024A Material Datasheet

Material Test Series Values

Material Standard Values

Material Models for Simulation

Material Description

Chemical Composition

Mechanical Properties

Physical Properties

Young's Modulus [GPa] vs Temperature [°C]

Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] vs Temperature [°C]

Creep Rupture Behaviour

Heat Treatment

Cross Reference

Producer/Supplier/Trade names

Material Compliance

Cu-DHP (CW024A; DIN EN 12163 : 1998-04)

Linear-elastic

Yield strength

Electrical resistivity

Coefficient thermal expansion

Specific heat

Density

Tensile strength

Thermal conductivity

Classification

Designation

Cu-DHP (soft annealed (+A); 4mm; not specified)

Strain life

Classification

Cu-DHP (soft annealed (+A); 6.35mm; not specified)

Strain life

Classification

Cu-DHP (soft annealed (+A); rod; 2.000-80.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R250; rod; 2.000-10.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R250; rod; 10.000-30.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R230; rod; 30.000-80.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R300; rod; 2.000-20.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R280; rod; 20.000-40.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R260; rod; 40.000-80.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (R350; rod; 2.000-10.000mm)

Yield strength

Tensile strength

Classification

Cu-DHP (hot rolled)

Yield strength

Tensile strength

Classification

Cu-DHP (soft annealed (+A))

Linear-elastic

Classification

Cu-DHP (cold formed)

Linear-elastic

Classification

Similar Materials